DIY: Dr. Seuss Birthday, Part I {Birthday Banner}

A Dr. Seuss Birthday Party: Birthday Banner

How to make your own birthday banner for a Dr. Seuss party

I'm so excited Baby G's birthday is almost here, but I've got so much to do now to prepare! I decided to be an overachiever and make everything, even though I've got a list of Christmas gifts to make and lots of birthdays to sew for this month. Oh well.

I started making this easy banner after my friend posted a tutorial on how she made hers. Instead of equilateral triangles though, I cut a 7" square in half (triangles) and used that. I didn't want to figure out the equilateral triangle... Ugh, geometry.

You can just follow my friend's tutorial for the first part of this, leaving out the end part where she sewed the triangles together at the top (wait for that until the end!).

I used an upcycled tshirt for the red and some leftover white fabric that I had for the white. For all the fabric that I cut, I was able to cut out both the front and back pieces of the square at once- with the white fabric, I just folded it in half, and with the t-shirt I was cutting through both sides of the t-shirt. Here's a picture of how to cut the triangles from your tshirt if you also decide to upcycle:


Cut the squares in half. At this point, you can just sew the triangles right sides together along the right and left sides of the triangles, leaving the top open. Cut away the corners and trim excess seam allowance. Turn right sides out. I ironed, then topstitched the sides because I love topstitching.


For my banner, I wanted to add "Happy Birthday" lettering to it. You could've done it before sewing the triangles together too. I decided to embroider my letters into the blue fabric, then put a frame around each letter to cut out.

Quick for the embroidery piece, seeing most of you will probably know how to embroider- I hooped my blue fabric with my stabilizer (I used tear away because that's what I had), then did my letters two at a time on my 4x4 hoop. You have to place them pretty carefully to avoid hitting the sides of the hoop or not being able to put two on one piece of fabric.

For sizes:
-My letters are 5mm high
-My circle with scalloped edges is 5.8 x 5.8mm.
-The capital letters ended up having a bit larger circle.

If you embroider the letter first, then you just setup the circle so that the middle is approximately at the center of the letter. Then you test to make sure it fits- a feature on my PE770 allows me to run through where the edges are for the embroidery that I'm setting it for.

Alternatively, you can do the circle first and center the letter inside it. Again, don't forget for the capital letters that you may need to tweak the size of the circle (I think I did 6.0 for the B). Don't make them too big or you'll end up not fitting them on your triangles!

Once you've got them all embroidered, just tear away the stabilizer and I cut in a circle around my embroidery.
I decided to use HeatNBond Lite (hope that's the whole of what it's called) to attach my letters to the banner. It's got two sides to it that can both be ironed to fabric. One side is really rough feeling- that's the side we work with first. Cut out circles of this for each letter, place the rough side of it towards the backs of your letters, then cover with a scrap piece of cloth and hold the iron over each letter for a few seconds. Check to see if it's on good, then do the others.

Left: This is a picture of the cut out circle. In this picture the non rough side is facing up. When you iron it onto the back of the letter, you're going to turn it the other way so the rough side touches the back of the d.

Right: Picture of the scrap fabric over the letters. I don't want my iron touching the letters directly.



Layout your triangles exactly how you want them in terms of colors. I did red-white alternating with enough triangles for each letter, plus one extra in the middle for the "space" between happy and birthday. See if your bias tape is long enough for all of this! You can always overlap two sets of bias tape if needed but it's nice to know in advance so you can plan accordingly. Mine only used one set.


Once you're done organizing, you can peel off the other side of the HeatNBond. You can place the letters onto the triangles exactly how you'd like them, then you place the scrap fabric over each and iron each letter on. Again, hold for a few seconds then check to see if it's on. Make sure you take off the peel before ironing each!

Once you do each of these, you are ready to finish up your banner.


Layout your triangles in order... I overlapped mine by 2.5". This makes them somewhat thick so I decided to change to a sharper needle. I originally started with my ballpoint because I'd been cloth diaper sewing recently. I pinned my triangles at a lower point so they'd stay in place when I shifted them over to my machine.


Grab your bias tape and insert the top of the triangles inside it. You can just use a straight stitch to sew it all together. Trim your remaining bias tape so each side is equal. All done!

 



For the ends, fold the rough edges over and then continue your
straight stitch across so that the raw edge doesn't show anymore.

Finished Product

I really like how this came out. My only frustration is that the embroidery and probably the heat of ironing caused the bubbling around the letters. I'm not sure how to avoid that, except maybe to do what I suggest below in my alternatives notes. That being said, it looks fine as is.



I had extra bias tape and extra triangles so I made another banner that's shorter with just the red and white colors, no lettering. I did not overlap the triangles when sewing the bias tape on here because I wanted to spread them out more on this so the banner would be longer.



Alternatives to this process: Instead of using HeatNBond, you could use the glue that washes out to put your letters onto the triangles. That way you could remove them to reuse the banner if you wanted.

I also didn't think of it when I made mine, but you could add some snaps or some way to hang the banner up at each end. That would be super useful.

COMMENTS

Name

*foodbeverage,16,*home&garden,40,*kids,18,alcoholic beverages,11,blogging,10,Children's Decor,25,cleaning,52,cloth diapers,36,clothing,16,computers,10,Cooking,54,Costumes,12,decorating,39,diy,103,eBook,2,Educational Activities with Kids,30,Epic Playroom Ideas,9,featured,4,food,19,Furniture for Kids,6,gardening,32,gifts,92,Gifts from Kids,7,go green,46,health,25,Holiday Ideas with Kids,11,holidays,47,home,57,Kid Friendly Food,10,Maryland local,6,Organizing for Kids,16,outdoors,32,Outdoors with Kids,18,painting,27,paper crafts,21,Parenting Ideas,47,Pets,21,photography,1,Pretend Play,10,Printable,6,psychotherapy,2,recipes,57,Review,18,saving money,15,Service Projects,4,sewing,212,Sewing for Kids,62,sleep,2,Sous Vide,1,Sustainable Sundays Link Party,25,travel,10,Travel with Kids,10,upcycling,68,Updating and Fixing Toys,3,woodworking,61,
ltr
item
DIY Danielle: DIY: Dr. Seuss Birthday, Part I {Birthday Banner}
DIY: Dr. Seuss Birthday, Part I {Birthday Banner}
A Dr. Seuss Birthday Party: Birthday Banner
http://1.bp.blogspot.com/-nqppGzrSSEE/UyMBDOS77DI/AAAAAAAARDM/Lmx0gfTVIhQ/s1600/diybirthdaybanner.jpg
http://1.bp.blogspot.com/-nqppGzrSSEE/UyMBDOS77DI/AAAAAAAARDM/Lmx0gfTVIhQ/s72-c/diybirthdaybanner.jpg
DIY Danielle
http://www.diydanielle.com/2012/08/dr-seuss-birthday-part-i-birthday-banner.html
http://www.diydanielle.com/
http://www.diydanielle.com/
http://www.diydanielle.com/2012/08/dr-seuss-birthday-part-i-birthday-banner.html
true
4345958580999046573
UTF-8
Loaded All Posts Not found any posts VIEW ALL Readmore Reply Cancel reply Delete By Home PAGES POSTS View All RECOMMENDED FOR YOU LABEL ARCHIVE SEARCH ALL POSTS Not found any post match with your request Back Home Sunday Monday Tuesday Wednesday Thursday Friday Saturday Sun Mon Tue Wed Thu Fri Sat January February March April May June July August September October November December Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec just now 1 minute ago $$1$$ minutes ago 1 hour ago $$1$$ hours ago Yesterday $$1$$ days ago $$1$$ weeks ago more than 5 weeks ago Followers Follow THIS CONTENT IS PREMIUM Please share to unlock Copy All Code Select All Code All codes were copied to your clipboard Can not copy the codes / texts, please press [CTRL]+[C] (or CMD+C with Mac) to copy